I also took a look in this router. The serial port works fine, yet the cfe bootloaded seems locked (while is booting dosen't give you the opportunity to stop the process). After the boot process they did provide a shell but they ask for login credentials. Which still don't know.
I took a look at the firmware update. Extracting from the jffs2 partition didn't work very well for me. I see the formal linux structure (etc, root, bin ..) yet the only folder having files is the /bin which is not particular useful. Did anyone had any success extracting the /etc folder ?
My guess at this point is that a nand flash dump is the way to proceed or a exploit in the web ui that can give us root and continue for there.
that the boot log:
----
BTL1
V1.1
CPUI
L1CI
PMCI
PMCS
AFEL
PWRZ
MEML
PMCD
CPUI
L1CI
ZBSS
CODE
DATA
L12F
MAIN
OTP?
MFGZ
OTPP
USBT
SNAN
PASS
----
HELO
CPUI
L1CI
4.1602-1.0.38-116.118
PMCI
PMCM
DRAM
----
PHYS
PHYE
DDR1
400H
SIZ4
LMBE
RACE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
MGIC
RAM1
Base: 4.16_02
CFE version 1.0.38-116.118 for BCM963381 (32bit,SP,BE)
Build Date: Thu Nov 16 19:47:34 CST 2017 (xialei@localhost.localdomain)
Copyright (C) 2000-2013 Broadcom Corporation.
Chip ID: BCM63381B0, MIPS: 600MHz, DDR: 400MHz, Bus: 300MHz
Main Thread: TP0
Total Memory: 134217728 bytes (128MB)
Boot Address: 0xb8000000
SPI NAND flash device: Winbond W25N01GV, id 0xefaa block 128KB size 131072KB
pmc_init:PMC using DQM mode
board_device_init, set not used GPIO to 0 OK!
Info: get a version head, the integrality is OK!
Info: start_block:[120],kernel_magic_head at :[120], i:[257],ver_blocks:[137]
Info: get a version head, the integrality is OK!
Info: start_block:[288],kernel_magic_head at :[288], i:[425],ver_blocks:[137]
Entering norm mode ...
Info: start_block:120
Info: bad blocks before fs:0
Info: pL->dwFsStartPhyAddr:10a0000
Info: pL->fs_len:f80000
para->BootParaCksum=0001e693
Decompression OK!
Entry at 0x803976c0
Starting program at 0x803976c0
Linux version 3.4.11-rt19 (xialei@localhost.localdomain) (gcc version 4.6.2 (Buildroot 2011.11) ) #1 SMP PREEMPT Mon Mar 19 17:38:03 CST 2018
963381REF2 prom init
Check boot para cksum...
boot para cksum OK!
********************BOOT INFO**************************
version_sum: : 2
version_nummax: : 2
dwCurrVersionIndex: : 0
dwBackVersionIndex: : 1
dwVersionStartPhyAddr 0: f00000
dwHeadRealPhyAddr 0: 2020000
dwIsCurrentVersion 0: 1
dwVersionIsBad 0: 0
dwVersionStartPhyAddr: 1: 2400000
dwHeadRealPhyAddr: 1: 3520000
dwIsCurrentVersion: 1: 0
dwVersionIsBad 1: 0
******************************************************
pdt_verinfo_init: tcVerInfo->RunMode[3]
bootPara.bootWhichImg=0
bootPara.img_info_tbl[0].flashOffset=0x 0
sHardVersion=V1.0
bootPara.runmode=3
CPU revision is: 0002a081 (Broadcom BMIPS4350)
DSL SDRAM reserved: 0x132000
Determined physical RAM map:
memory: 07ece000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00007ece
Movable zone start PFN for each node
Early memory PFN ranges
0: 0x00000000 -> 0x00007ece
On node 0 totalpages: 32462
free_area_init_node: node 0, pgdat 804b1750, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 222 pages used for memmap
Normal zone: 28144 pages, LIFO batch:7
PERCPU: Embedded 7 pages/cpu @81103000 s5632 r8192 d14848 u32768
pcpu-alloc: s5632 r8192 d14848 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32208
Kernel command line: root=31:9 ro rootfstype=jffs2 irqaffinity=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 122200k/129848k available (3668k kernel code, 7648k reserved, 1076k data, 240k init, 0k highmem)
Preemptible hierarchical RCU implementation.
NR_IRQS:128
console [ttyS0] enabled
Allocating memory for DSP module core and initialization code
Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
Calibrating delay loop... 598.01 BogoMIPS (lpj=299008)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
--Kernel Config--
SMP=1
PREEMPT=1
DEBUG_SPINLOCK=0
DEBUG_MUTEXES=0
Broadcom Logger v0.1 Mar 19 2018 17:37:42
CPU revision is: 0002a081 (Broadcom BMIPS4350)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Brought up 2 CPUs
NET: Registered protocol family 16
pmc_init:PMC using DQM mode
1192:57:47 [Klogctl][Info] [(562)LogCtlInit] LogCtlInit begin
1192:57:47 [Klogctl][Info] [(579)LogCtlInit] LogCtlInit end
1192:57:47 [Kern][Notice] [monitor.c(938)MonitorInit] cspmonitor init... !
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom GBPM v0.1 Mar 19 2018 17:37:43 initialized
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x10600000-0x106fffff]
pci_bus 0000:00: root bus resource [io 0x11700000-0x1170ffff]
pci 0000:00:09.0: [14e4:6300] type 00 class 0x0c0310
pci 0000:00:09.0: reg 10: [mem 0x1000c400-0x1000c4ff]
pci 0000:00:0a.0: [14e4:6300] type 00 class 0x0c0320
pci 0000:00:0a.0: reg 10: [mem 0x1000c300-0x1000c3ff]
PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [mem 0xa0000000-0xbfffffff]
pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
pci 0000:01:00.0: [14e4:6338] type 01 class 0x060400
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:02:00.0: [14e4:a8db] type 00 class 0x028000
pci 0000:02:00.0: reg 10: [mem 0x00000000-0x00007fff 64bit]
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: BAR 8: assigned [mem 0xa0000000-0xa00fffff]
pci 0000:02:00.0: BAR 0: assigned [mem 0xa0000000-0xa0007fff 64bit]
pci 0000:01:00.0: PCI bridge to [bus 02-02]
pci 0000:01:00.0: bridge window [mem 0xa0000000-0xa00fffff]
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
skbFreeTask created successfully
NET: Registered protocol family 8
NET: Registered protocol family 20
1192:57:47 [Kern][Info] [qos.c(5055)CSPKernel_QoS_I] Qos module init
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS 16 bytes, default 16
init_bcm_tstamp: unhandled mips_hpt_freq=300000000, adjust constants in bcm_tstamp.c
bcm_tstamp initialized, (hpt_freq=300000000 2us_div=300 2ns_mult=0 2ns_shift=0)
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 238
io scheduler noop registered (default)
brd: module loaded
loop: module loaded
SPI NAND Device Linux Registration
SPI NAND Linux Registration
SPI NAND device reset
Found SPI NAND device Winbond W25N01GV
SPI NAND device Winbond W25N01GV
device id = 0xefaa
page size = 0x800
block size = 0x20000
total blocks = 0x400
total size = 0x8000000
NAND device: Manufacturer ID: 0xef, Chip ID: 0xaa (Winbond NAND 128MiB 1,8V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended!
Creating 10 MTD partitions on "Winbond W25N01GV":
0x000000000000-0x000000220000 : "boot"
0x000000220000-0x000000320000 : "tag"
0x000000320000-0x0000004a0000 : "userconfig"
0x0000004a0000-0x000000620000 : "backconfig"
0x000000620000-0x0000007a0000 : "defconfig"
0x0000007a0000-0x000000920000 : "log"
0x000000920000-0x000000aa0000 : "env"
0x000000f00000-0x000002400000 : "rootfs1"
0x000002400000-0x000003900000 : "rootfs2"
0x0000010a0000-0x000002020000 : "filesystem"
brcmboard: brcm_board_init entry
Failed to create a netlink socket for monitor
DYING GASP IRQ initialized
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xb0000280 (irq = 8) is a BCM63XX
ttyS1 at MMIO 0xb00002a0 (irq = 9) is a BCM63XX
Total # RxBds=5154
bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
BPM: tot_mem_size=134217728B (128MB), buf_mem_size <15%> =20132655B (19MB), num of buffers=9679, buf size=2080
Broadcom BPM Module Char Driver v0.1 Mar 19 2018 17:37:47 Registered<244>
Info:zte_watchdog_init, errorEPC = 0f7e7716
pktgen: Packet Generator for packet performance testing. Version: 2.74
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1909 buckets, 7636 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
1192:57:48 [Kern][Info] [br_com_special_(109)arp_stolen_init] arp_stolen firewalling registered
Bridge firewalling registered
Ebtables v2.0 registered
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
PPP generic driver version 2.4.2
NET: Registered protocol family 24
1192:57:48 [Kern][Info] [ver_info_nand.c(457)ver_info_init] ver_info_init
1192:57:48 [Kern][Notice] [csp_ifinfo.c(219)csp_ifinfo_init] Initializing CSP IFinfo...
1192:57:48 [Kern][Notice] [sweth_core.c(2760)sweth_init] SWÐ HAL driver initing!
1192:57:48 [Kern][Notice] [sweth_core.c(140)CreateSwEthObjs] Create SW & ETH objects
1192:57:48 [Kern][Notice] [sweth_core.c(156)CreateSwEthObjs] Failed to get SWITCH attr, iRet=-2
1192:57:48 [Kern][Info] [sweth_core.c(163)CreateSwEthObjs] nEmac = 1, nSw = 0, nEth=4.
1192:57:48 [Kern][Warn] [sweth_core.c(310)CreateSwEthObjs] Failed to get TAG_PARA_MAC1!
1192:57:48 [Kern][Info] [sweth_core.c(322)CreateSwEthObjs] ETH obj0: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 1
1192:57:48 [Kern][Warn] [sweth_core.c(310)CreateSwEthObjs] Failed to get TAG_PARA_MAC1!
1192:57:48 [Kern][Info] [sweth_core.c(322)CreateSwEthObjs] ETH obj1: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 2
1192:57:48 [Kern][Warn] [sweth_core.c(310)CreateSwEthObjs] Failed to get TAG_PARA_MAC1!
1192:57:48 [Kern][Info] [sweth_core.c(322)CreateSwEthObjs] ETH obj2: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 3
1192:57:48 [Kern][Warn] [sweth_core.c(310)CreateSwEthObjs] Failed to get TAG_PARA_MAC1!
1192:57:48 [Kern][Info] [sweth_core.c(322)CreateSwEthObjs] ETH obj3: PhyType = 1, Is_assoc_sw = 0, Emac = 0, Phy = 4
Jiffies_test Driver Init Successfully
logger: created 1024K log 'logger_main' major '99'
: success register character device for /dev/monitor
1192:57:48 [Kern][Notice] [cspmirror.c(1245)mirror_init] ***********mirror_init************
systools version:v0.7.0
errorEPC = 0f7e7716
1192:57:48 [Kern][Info] [br_multicast_se(7234)br_mcparam_init] info init!
1192:57:48 [Kern][Info] [qp_meter_api.c(66)QoSPolicerMeter] Register Meter(stb)
1192:57:48 [Kern][Info] [qp_meter_api.c(66)QoSPolicerMeter] Register Meter(srtc)
1192:57:48 [Kern][Info] [qp_meter_api.c(66)QoSPolicerMeter] Register Meter(trtc)
1192:57:48 [Kern][Info] [qp_meter_api.c(66)QoSPolicerMeter] Register Meter(hard)
1192:57:48 [Kern][Info] [qp_act_api.c(66)QoSPolicerActRe] Register Action(null)
1192:57:48 [Kern][Info] [qp_act_api.c(66)QoSPolicerActRe] Register Action(drop)
1192:57:48 [Kern][Info] [qp_act_api.c(66)QoSPolicerActRe] Register Action(dscp_mark)
1192:57:48 [Kern][Info] [qp_act_api.c(66)QoSPolicerActRe] Register Action(vlan_prio_mark)
1192:57:48 [Kern][Info] [qp_act_api.c(66)QoSPolicerActRe] Register Action(dscp_vlan_prio_mark)
child_dev_init start
child_dev_ioctl_set set[80393d20]
#######begin FDB_Notify Reg
#######after FDB_Notify Reg
#######begin FDB_Notify Reg
Shouldn't be in WHILE
#######after FDB_Notify Reg
1192:57:48 [Kern][Error] [ledkey_callback(26)keycallback_ini] Install WPS KEY Callback Failed!
VFS: Mounted root (jffs2 filesystem) readonly on device 31:9.
Freeing unused kernel memory: 240k freed
init normal mode!!!
Loading drivers and kernel modules...
jffs2: notice: (269) check_node_data: wrong data CRC in data node at 0x00161318: read 0x90074d32, calculated 0xe9fe5f3a.
mkdir: can't create directory '/defcfg/chain1': File exists
mkdir: can't create directory '/defcfg/chain2': File exists
chipinfo: module license 'proprietary' taints kernel.
Disabling lock debugging due to kernel taint
brcmchipinfo: brcm_chipinfo_init entry
bcmxtmrt: Broadcom BCM3381B0 ATM/PTM Network Device v0.6 Mar 19 2018 17:43:20
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM63381B0 Ethernet Network Device v0.1 Mar 19 2018 17:43:02
ETH Init: Ch:0 - 200 tx BDs at 0xa639c000
ETH Init: Ch:0 - 3871 rx BDs at 0xa5d18000
vport_cnt=4, consolidated_portmap=0xF
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
vport_id=0x1, logical_port=0x0
vnet_dev[vport_id=1]=eth0
ETH0-->eth0
eth0: <Int sw port: 0> <Logical : 00> PHY_ID <0x00000001 : 0x01> MAC : 00:D0:D0:00:00:01
vport_id=0x2, logical_port=0x1
vnet_dev[vport_id=2]=eth1
ETH1-->eth1
eth1: <Int sw port: 1> <Logical : 01> PHY_ID <0x00000002 : 0x02> MAC : 00:D0:D0:00:00:01
vport_id=0x3, logical_port=0x2
vnet_dev[vport_id=3]=eth2
ETH2-->eth2
eth2: <Int sw port: 2> <Logical : 02> PHY_ID <0x00000003 : 0x03> MAC : 00:D0:D0:00:00:01
vport_id=0x4, logical_port=0x3
vnet_dev[vport_id=4]=eth3
ETH3-->eth3
eth3: <Int sw port: 3> <Logical : 03> PHY_ID <0x00000004 : 0x04> MAC : 00:D0:D0:00:00:01
Ethernet Auto Power Down and Sleep: Enabled
Energy Efficient Ethernet: Enabled
#######begin FDB_Notify Reg
Shouldn't be in WHILE
Shouldn't be in WHILE
#######after FDB_Notify Reg
#######begin FDB_Notify Reg
Shouldn't be in WHILE
Shouldn't be in WHILE
Shouldn't be in WHILE
#######after FDB_Notify Reg
1192:58:01 [Kern][Notice] [bcm_emac_adapte(663)Register_bcm_em] Register BCM EMAC driver
1192:58:01 [Kern][Notice] [sweth_core.c(588)RegisterEmacDrv] Register EMAC driver
1192:58:01 [Kern][Notice] [sweth_core.c(429)InitSwEthObjs] Initialise SW & ETH objects
1192:58:01 [Kern][Warn] [sweth_core.c(1762)hal_set_port_ma] Driver do not support set MAC address!
1192:58:01 [Kern][Warn] [sweth_core.c(1762)hal_set_port_ma] Driver do not support set MAC address!
1192:58:01 [Kern][Warn] [sweth_core.c(1762)hal_set_port_ma] Driver do not support set MAC address!
1192:58:01 [Kern][Warn] [sweth_core.c(1762)hal_set_port_ma] Driver do not support set MAC address!
NComm TMS V6.80 Kernel Module loaded.
Loading PCM shim driver
Endpoint: endpoint_init entry
BOS: Enter bosInit
BOS: Exit bosInit
fxsnum 2,fx0 num 0 ,dect 0Endpoint: endpoint_init COMPLETED
Broadcom 802.1Q VLAN Interface, v0.1
ADDRCONF(NETDEV_UP): eth0: link is not ready
device eth0 entered promiscuous mode
Host MIPS Clock divider pwrsaving is enabled
/etc/init.norm: line 120: hostname: not found
sched_setaffinity cpu 0 (ret = 0)
1192:57:55 [User][Info] [mount_jffs2.c(37)main] mount dev is /dev/mtdblock2 mount point is /usercfg/
1192:57:55 [User][Info] [mount_jffs2.c(99)main] mtdInfo: /dev/mtd2 size=1572864, erasesize=131072 bad block count 0
1192:57:56 [User][Info] [mount_jffs2.c(161)main] mount dev /dev/mtdblock2 at dir /usercfg/ success
1192:57:56 [User][Info] [mount_jffs2.c(37)main] mount dev is /dev/mtdblock3 mount point is /backcfg/
1192:57:56 [User][Info] [mount_jffs2.c(99)main] mtdInfo: /dev/mtd3 size=1572864, erasesize=131072 bad block count 0
1192:57:56 [User][Info] [mount_jffs2.c(161)main] mount dev /dev/mtdblock3 at dir /backcfg/ success
1192:57:56 [User][Info] [mount_jffs2.c(37)main] mount dev is /dev/mtdblock4 mount point is /defcfg/
1192:57:56 [User][Info] [mount_jffs2.c(99)main] mtdInfo: /dev/mtd4 size=1572864, erasesize=131072 bad block count 0
1192:57:56 [User][Info] [mount_jffs2.c(161)main] mount dev /dev/mtdblock4 at dir /defcfg/ success
1192:57:56 [User][Info] [mount_jffs2.c(37)main] mount dev is /dev/mtdblock5 mount point is /log/
1192:57:56 [User][Info] [mount_jffs2.c(99)main] mtdInfo: /dev/mtd5 size=1572864, erasesize=131072 bad block count 0
1192:57:56 [User][Info] [mount_jffs2.c(161)main] mount dev /dev/mtdblock5 at dir /log/ success
1192:57:56 [User][Info] [mount_jffs2.c(37)main] mount dev is /dev/mtdblock6 mount point is /env/
1192:57:56 [User][Info] [mount_jffs2.c(99)main] mtdInfo: /dev/mtd6 size=1572864, erasesize=131072 bad block count 0
1192:57:56 [User][Info] [mount_jffs2.c(161)main] mount dev /dev/mtdblock6 at dir /env/ success
1192:58:04 [User][Warn] [ifconfig.c(957)ifconfig] Ioctl failed!SIOCSIFADDR
1192:58:04 [OSS][Notice] [pc.c(1907)initPCFd] open /dev/ptyp0 success.
(none)
PID: 344
1192:58:09 [User][Info] [db_shm_mgr.c(109)DBShmSrvInit] iShmId:32769
1192:58:09 [User][Info] [db_shm_mgr.c(124)DBShmSrvInit] pShmBuf:60000000
[log_file.c(1704)ProcLogConf] Set LOG_FILE_CONF_SET_PDTCONF.
[log_file.c(1768)ProcLogConf] Set cAutoSave = 1
[log_filesave.c(176)CheckLogConfFile] File not exist: filename(/log/flag_usrfs), Cnt=40
1192:58:10 [dhcps][Info] [dhcps.c(160)DHCPSInit] module init success!dhcp server
1192:58:10 [dhcp4c][Warn] [dhcp4c_inst.c(4402)_dhcp4cRegSendO] Send code[60]fun[0x58fbf4] is replaced by fun[0x594d60]
1192:58:10 [monitor][Info] [cspd_monitor.c(422)MonitorMain] monitor init success
1192:58:10 [PingTracert_mgr][Info] [tracert_mgr.c(1107)tracertInit] module init success!tracert mgr
1192:58:10 [ethlinkvlan][Info] [ifs_ethlinkvlan(2313)linkifMain] IfsMain recv event(4352) msgptr((nil)) len(0)
1192:58:10 [ethlinkvlan][Info] [ifs_ethlinkvlan(2181)linkifAsynmsg] lpMsg == NULL
1192:58:10 [ppp_mgr][Info] [ppp_mgr.c(6398)PPPInit] module init success!
1192:58:10 [ipif_mgr][Info] [ifs_ipif.c(2102)ifsIPIFMain] IfsMain recv event(0x1100) msgptr((nil)) len(0)
1192:58:10 [ipif_mgr][Info] [ipv4_addr_mgr.c(1294)ipv4AddrInit] [ipv4AddrInit] success
1192:58:10 [ipif_mgr][Info] [ifs_ipif.c(2085)ifsIPIFInit] [ifsIPIFInit] success
1192:58:10 [ipif_mgr][Info] [ifs_ipif.c(1910)ifsAsynmsg] unknown ASynMsg!msg id = 4352
1192:58:10 [addr6_mgr][Info] [addr6_mgr.c(3429)Addr6Main] wEvent=0x1100, wMsgType=1, wMsgLen=0, wState=0
1192:58:10 [prefix_mgr][Info] [prefix_mgr.c(3223)prefixInit] Prefix Init Success!
1192:58:10 [bridge][Info] [bridge.c(2161)bridgeInit] module init success!(bridge_mgr)
1192:58:10 [eth_mgr][Info] [eth_mgr.c(1847)ethInit] module init success!ethernet mgr
1192:58:10 [htat_mgr][Info] [htat_mgr.c(2075)htatInit] module init success!htat_mgr init
1192:58:10 [dsl_mgr][Info] [dsl_mgr.c(3468)dsl_init] dsl init ok
1192:58:10 [xtm_mgr][Info] [xtm_mgr.c(4252)xtmInit] [xtmInit] start
1192:58:10 [xtm_mgr][Info] [xtm_mgr.c(4278)xtmInit] xtm init ok
1192:58:10 [xtm_mgr][Info] [xtm_mgr.c(4280)xtmInit] xtm support dynamic add/del interface
1192:58:10 [ptry_mgr][Info] [ptry_mgr.c(478)ptryMgrInit] module init success!(PTry mgr)
1192:58:10 [route_mgr][Info] [policy_route.c(1646)policyRtTableIn] policyRtTableInit ok
1192:58:10 [route_mgr][Info] [policy_route.c(1561)defPolicyRtChai] defPolicyRtChainInit ok
1192:58:10 [route_mgr][Info] [rip_mgr.c(39)RIPInit] Common Info: rip init
1192:58:10 [route_mgr][Info] [ripng_mgr.c(39)RIPngInit] Common Info: ripng init
1192:58:10 [route_mgr][Info] [route_mgr.c(802)routeInit] SubScribPublish DefGW Service OK
1192:58:10 [binding_mgr][Info] [binding_mgr.c(1666)bindingInit] [bindingInit] end
1192:58:10 [qos_mgr][Info] [qos_default_qdi(2246)RegisterDefault] RegisterDefaultIFQdisc. IF WAN&DEV.BRIDGING.BR1.BRPORT, Qdisc CSPDefSPWRRWFQ
1192:58:10 [qos_mgr][Info] [interface_api.c(1560)RegisterNetIFNo] RegisterNetIFNotify start, event[6] IF_ID[] WanLan[3] Handle[0x4c42dc]
1192:58:10 [qos_mgr][Info] [interface_api.c(1603)RegisterNetIFNo] Reg NetIF Notify ok, IF_ID[], WanLan[3], pHandle[0x4c42dc], Event[6]
1192:58:10 [qos_mgr][Info] [interface_api.c(1560)RegisterNetIFNo] RegisterNetIFNotify start, event[6] IF_ID[DEV.PTM.LINK1] WanLan[3] Handle[0x4c4088]
1192:58:10 [qos_mgr][Info] [interface_api.c(1573)RegisterNetIFNo] IF_ID Not Null[DEV.PTM.LINK1]
1192:58:10 [qos_mgr][Info] [interface_api.c(1603)RegisterNetIFNo] Reg NetIF Notify ok, IF_ID[DEV.PTM.LINK1], WanLan[3], pHandle[0x4c4088], Event[6]
1192:58:10 [sntp_mgr][Info] [time_policy.c(101)TpInit] module init success!3
1192:58:10 [sntp_mgr][Info] [sntp_mgr.c(1694)sntpInit] module init success!SNTP mgr
1192:58:10 [ddns_mgr][Info] [ddns_mgr.c(1539)ddnsInit] module init success!ddns_mgr
1192:58:10 [dns_mgr][Info] [dns_mgr.c(437)dnsInit] SubScribPublish NetIF Service OK
1192:58:10 [dns_mgr][Info] [comp_dns_mgr.c(76)CompDnsInit] Init Comp_Dns_Mgr Success!
1192:58:10 [fm_mgr][Info] [fm_mgr.c(2641)fmServerInit] module init success!Enter FmServer Init!
1192:58:10 [fm_mgr][Info] [fm_mgr.c(4236)fmMgrInit] module init success!fm mgr
1192:58:10 [tr143_mgr][Info] [tr143_mgr.c(547)tr143Init] module init success!tr143 mgr
1192:58:10 [ipv6_tunl_mgr][Info] [ipv6_tunl_mgr.c(416)IPv6TunlMgrMain] wEvent=0x1100, wMsgType=1, wMsgLen=0, wState=0
1192:58:10 [ipv6_tunl_mgr][Info] [tunl46_mgr.c(1851)TunnelMain] wEvent=0x1100, wMsgType=1, wMsgLen=0, wState=0
1192:58:10 [ipv6_tunl_mgr][Info] [tunl46_mgr.c(1617)TunnelMgrInit] [TunnelMgrInit] start
1192:58:10 [ipv6_tunl_mgr][Info] [tunl46_mgr.c(1622)TunnelMgrInit] [TunnelMgrInit] OK
1192:58:10 [ipv6_tunl_mgr][Info] [tunl64_mgr.c(1826)Tunl64Main] wEvent=0x1100, wMsgType=1, wMsgLen=0, wState=0
1192:58:10 [fon_mgr][Info] [fon_mgr.c(3915)FonMain] wEvent=0x1100, wMsgType=1, wMsgLen=0, wState=0
1192:58:10 [ipif_mgr][Info] [ifs_netif.c(2579)interfaceNotify] [interfaceNotifyHook] start, to pid[10103]
1192:58:10 [ipif_mgr][Info] [ifs_netif.c(2579)interfaceNotify] [interfaceNotifyHook] start, to pid[10103]
1192:58:10 [DB][Error] [dbc_mgr_tbl.c(494)dbCreateDomainN] create table fail (ParentControlUser) domain(FilterMode) error default value
1192:58:10 [DB][Info] [dbc_tbl_wol_inf(18)dbCreateWolInfo] call dbCreateWolInfoTbl
1192:58:10 [DB][Error] [dbc_def_dev_inf(176)setVerNumFromFi] /etc/ver_num_des file open error!
1192:58:10 [DB][Warn] [dbc_mgr_tbl.c(1662)dbSetValComm] not find domain table(WLANBase) domain(AutoChannelFrom)
1192:58:10 [DB][Warn] [dbc_mgr_tbl.c(1662)dbSetValComm] not find domain table(WLANBase) domain(AutoChannelTo)
1192:58:10 [DB][Error] [dbc_mgr_def.c(79)dbMgrStaticSetI] not find table (PDTWLANWAPI)
1192:58:10 [DB][Info] [dbc_def_wol_inf(22)dbDefWolInfo] call dbDefWolInfo
1192:58:10 [DB][Info] [dbc_init_pdt_in(2485)dbCheckSingleCf] DB Decry cfg end (iRet: 0)
1192:58:10 [DB][Warn] [dbc_mgr_file_xm(1688)_dbXMLTblChk] load database failed table(L2BAvailIF) cut or exceed max row or unequal row.
1192:58:10 [DB][Warn] [dbc_mgr_file_xm(1688)_dbXMLTblChk] load database failed table(BrFilter) cut or exceed max row or unequal row.
1192:58:11 [DB][Info] [dbc_person_teln(66)dbPersonInitTel] set password
1192:58:11 [DB][Info] [dbc_mgr_file.c(1250)dbFileLoadCfg] find file /var/tmp/db_Decry_cfg.xml
1192:58:15 [DB][Info] [dbc_mgr_file.c(2290)dbInitSignVal] szCfgSignVal= Speedport Entry 2i,iRet:0
1192:58:15 [DB][Info] [dbc_init_pdt_in(1636)_PdtDBTransferC] [_PdtDBTransferCfg] dwFlagVerNum=12, dwFlagVerNumExt=5
1192:58:15 [DB][Info] [dbc_core.c(1249)dbEndTm] (ALL) end, use 455 tick
1192:58:15 [OSS][Warn] [oss_sche.c(868)RunProcess] RunProcess process[DB] Event[0x1100] dwUsedTicks[483]
----------------------------------------------[log_file.c(1444)ProcLogConf] Set SaveEnable=1
1192:58:15 [dhcp6s][Info] [ipif_api.c(2190)RegAddr6Notify] RegAddr6Notify start, event[3] IF_ID[] WanLan[2] Handle[0x59cdc8]
1192:58:15 [PingTracert_mgr][Info] [tracert_mgr.c(1134)tracertStart] module start success!tracert mgr
1192:58:15 [srm_mgr][Info] [srm_mgr.c(228)SrmInit] module init success!use SRM_DBVIEW data
1192:58:15 [adev_mgr][Info] [extend_options.(121)CspAddParseOptP]